Adjusting The Rear Brake
1. Check brake pedal position distance from the top of the rider footrest to the top of the brake pedal Out of specification Adjust. Brake pedal position below the top of the rider footrest 25.8 mm 1.02 in b. Turn the adjusting bolt in direction or until the specified brake pedal position is obtained.
General Tightening Torque Specifications
This chart specifies tightening torques for standard fasteners with a standard ISO thread pitch. Tightening torque specifications for special components or assemblies are provided for each chapter of this manual. To avoid warpage, tighten multi-fastener assemblies in a crisscross pattern and progressive stages until the specified tightening torque is reached. Unless otherwise specified, tightening torque specifications require clean, dry threads. Components should be at room temperature. A...
seat Vvv
front cowling inner panel left and right Refer to COWLINGS.
Eas00026
Make sure all connections are tight. If there is no continuity, clean the terminals. When checking the wire harness, perform steps 1 to 3 . As a quick remedy, use a contact revitalizer available at most part stores.
Throttle body
b. Turn the adjusting nut in direction or to take up any slack on the decelerator cable. Throttle cable free play is increased. Throttle cable free play is decreased. If the specified throttle cable free play cannot be obtained on the carburetor side of the cable, use the adjusting nut on the handlebar side.
Checking The Engine Oil Level
1. Stand the motorcycle on a level surface. Place the motorcycle on a suitable stand. Make sure the motorcycle is upright. 2. Start the engine, warm it up for several minutes, and then turn it off. The engine oil level should be between the minimum level mark and maximum level mark . Below the minimum level mark Add the recommended engine oil to the proper level. AT 5 C 40 F or higher A Yamalube 4 20W40 or SAE 20W40 type SE motor oil AT 15 C 60 F or lower B Yamalube 4 10W30 or SAE 10W30 type SE...
Engine Specifications
Standard compression pressure at sea level Liquid-cooled, 4-stroke, DOHC 600 cm3 36.61 cu.in Forward-inclined parallel 4-cylinder 65.5 x 44.5 mm 2.58 x 1.75 in 12.2 1 1,250 - 1,350 r min 29 kPa 218 mmHg, 8.6 inHg 1,550 kPa 15.50 kg cm2,15.50 bar, 220.46 psi at 400 r min Recommended fuel Fuel tank capacity Total including reserve Reserve only 19.4 L 4.25 lmp gal, 5.1 US gal 3.6 L 0.79 lmp gal, 0.9 US gal Quantity Total amount Without oil filter cartridge replacement With oil filter cartridge...
Yamaha Fz8 Carbon
Make sure all of the cables and wires are properly routed. a. Point the front wheel straight ahead. b. Install a plastic locking tie loosely around the end of the handlebar as shown. c. Hook a spring gauge 2 onto the plastic locking tie. d. Hold the spring gauge at a 90o angle from the handlebar, pull the spring gauge, and then record the measurement when the handlebar starts to run.
Removing The Fuel Tank
1. Extract the fuel in the fuel tank through the fuel tank cap with a pump. Although the fuel has been removed from the fuel tank, be careful when removing the fuel hoses, since there may be fuel remaining in it. Before removing the hoses, place a few rags in the area under where it will be removed. Do not set the fuel tank down so that the installation surface of the fuel pump is directly under the tank. Be sure to lean the fuel tank in an upright position. REMOVING THE FUEL PUMP 1. Remove...
Ym01253
These tools are used to remove or install the valve assemblies. Middle driven shaft bearing driver 90890-04058 YM-4058 Mechanical seal installer 90890-04078 YM-33221 Middle driven shaft bearing driver Mechanical seal installer These tools are used to install the water pump seal.
Info Ans
Starter clutch idle gear inner surface Transmission gears wheel and pinion Shift forks and shift fork guide bars Generator rotor cover stator coil assembly lead grommet Pickup rotor cover crankshaft position sensor lead grommet
Adjusting The Exhaust Gas Volume
Be sure to set the carbon monoxide density to standard, and then adjust the exhaust gas. 1. Turn the main switch to OFF and engine stop switch ON. 2. While keeping the SELECT and RESET buttons pressed simultaneously, turn ON the main switch keep them pressed for 8 seconds or more . All indications on the meter disappear except the clock and trip indications. Letters dIAG appear on the odo meter LCD. 3. Using the SELECT button, select either the Co adjustment mode which appears as Co or the...
Fi System
The fuel pump delivers fuel to the injector via the fuel filter. The pressure regulator maintains the fuel pressure that is applied to the injector at only 250 kPa 2.5 kg cm2 . Accordingly, when the energizing signal from the ECU energizes the injector, the fuel passage opens, causing the fuel to be injected into the intake manifold only during the time the passage remains open. Therefore, the longer the length of time the injector is energized injection duration , the greater the volume of...
Outline Of Fi System
The main function of a fuel supply system is to provide fuel to the combustion chamber at the optimum air-fuel ratio in accordance with the engine operating conditions and the atmospheric temperature. In the conventional carburetor system, the air-fuel ratio of the mixture that is supplied to the combustion chamber is created by the volume of the intake air and the fuel that is metered by the jet used in the respective carburetor. Despite the same volume of intake air, the fuel volume...
Adjusting The Valve Clearance Synchronizing The Throttle Bodies
For installation, reverse the removal procedure. SYNCHRONIZING THE THROTTLE BODIES NOTE Prior to synchronizing the throttle bodies, the valve clearance and the engine idling speed should be properly adjusted and the ignition timing should be checked. 1. Stand the motorcycle on a level surface. NOTE Place the motorcycle on a suitable stand. front cowling inner panel left and right Refer to COWLINGS Refer to AIR FILTER CASE. vacuum gauge onto the synchronizing hose 2 Refer to AIR FILTER CASE....
Checking The Exhaust System
The following procedure applies to all of the exhaust pipes and gaskets. 1. Remove radiator Refer to RADIATOR in chapter 6. 20 Nm 2.0 m kg, 15 fWb Catalyst joint bolt 20 Nm 2.0 m kg, 15 fWb Muffler joint bolt 7 Muffler and muffler stay 8 20 Nm 2.0 m kg, 15 fWb Exhaust pipe and exhaust pipe stay 9 20 Nm 2.0 m kg, 15 fWb Catalyst pipe and catalyst pipe stay 10 4. Install radiator Refer to RADIATOR in chapter 6.
Adjusting The Clutch Cable Free Play Cleaning The Air Filter Element
Refer to AIR FILTER CASE. front cowling inner panel left and right Refer to COWLINGS.
Note
Refer to CAMSHAFTS in chapter 5. When removing the timing chain and camshafts, fasten the timing chain with a wire to retrieve it if it falls into the crankcase. a. Remove the valve lifter and the valve pad 2 with a valve lapper 3.
Eas00897
The injection duration and the injection timing are controlled by the ECU. Signals that are input from the throttle position sensor, crankshaft position sensor, intake air pressure sensor, intake temperature sensor and coolant temperature sensor enable the ECU to determine the injection duration. The injection timing is determined through the signals from the crankshaft position sensor. As a result, the volume of fuel that is required by the engine can be supplied at all times in accordance...
Dc Tci
248 372 Q at 20 C 68 F Gy-B F8T811 MITSUBISHI Model manufacturer Minimum ignition spark gap Primary coil resistance Secondary coil resistance 1.53 2.07 Q at 20 C 68 F 12.0 18.0 kQ at 20 C 68 F Regulator type Model manufacture No-load regulated voltage Rectifier capacity Withstand voltage Semi conductor short circuit SH719AA SHINDENGEN 14.1 14.9 V 18 A 240 V Battery voltage capacity Specific gravity Manufacturer Ten hour rate amperage